Show the number+335 86 24 00 26

Used front axle Case IH

244 available products

A faulty front axle on a Case IH tractor or combine harvester can immobilize the machine at the worst possible time and requires a swift response. TMC Bejenne offers a wide selection of used complete front axles sourced from dismantled Case IH equipment: tractors from the Puma, Maxxum, MXU, CVX, Magnum, CS ranges and numeric series, as well as Axial-Flow combines. Each axle is inspected in our workshop by our specialized technicians before dispatch, with traceability based on the source machine model. You gain access to reliable references at a significantly lower cost than new, within a circular economy framework upheld by TMC Bejenne since 1945.

 Bevel gear(22)
 Complete front axle(76)
 Front Axle Frame(15)
 Front Axle Housing(23)
 Kingpin(18)
 Transfer Case(3)
 Wheel Reducer(49)

Case IH tractor front axle: operation and available components

The front axle of a Case IH tractor provides 4WD traction, steering, and on recent models, absorbs ground irregularities through an integrated suspension. It is made up of several distinct parts: the axle cradle (supporting frame), the transfer case that receives torque from the gearbox, the bevel gear for angle transfer, the steering knuckles, the planetary wheel reducers, and the drive shafts. All spare parts for the front axle are available at TMC Bejenne in used condition, either individually or as a complete axle, depending on your needs.

Case IH front axles available at TMC Bejenne: tractors and combines

  • Puma range tractors: Puma 140, Puma 150 CVX, Puma 160 CVX, Puma 180, Puma 195, Puma 240 CVX
  • Maxxum range tractors: Maxxum 5120, Maxxum 5140, Maxxum 110, Maxxum 125
  • MXU and MX range tractors: MXU 115, MXU 125, MX 170, MXM 175
  • CVX and CS range tractors: CVX 130, CS 86, CS 150
  • Numeric and classic series: 845 XL, 956, 956 XL, 4220, 4230, 1455 XL
  • Axial-Flow combines: 1660, 1680, 2166, 2188, 2366, 2388, 6088, 7130
  • Complete axles or spare parts (knuckle, reducer, shaft, bevel gear, housing)
  • Stock exceeding 25,000 references, shipping across France and internationally

ZF front axle Case IH: the standard transfer case on modern ranges

The ZF front axle equips the majority of Case IH tractors from the Puma, Maxxum, CVX, and MXU series since the 2000s. ZF (Zahnradfabrik Friedrichshafen) is the leading supplier for these axles, also found on New Holland and Massey Ferguson tractors of equivalent generations. Common wear parts include cross shafts and drive shafts (subject to traction shocks and significant angles in turns), steering knuckle seals (exposed to dirt projection and pressure variations), and epicyclic wheel reducers (gradual wear under heavy load). TMC Bejenne offers complete front axles sourced from end-of-life Case IH machines, inspected to check bearing condition, seal tightness, and backlash in bevel gears.

Case IH front axle leaks and seals: replacement parts available

  • Leak at knuckles: replacement of knuckle seal or oil seal, check associated wheel hub condition
  • Leak at transfer case: central seal to identify depending on axle type (ZF or Dana)
  • Leak at wheel reducer: planetary seal or output shaft seal ring
  • Case IH front axle seals: identify exact reference by tractor model and front axle serial number
  • Damaged axle nose: replace complete transfer case if the crack affects the main housing
  • Wheel hub: also available within the TMC Bejenne axle range
  • For remote diagnosis, contact our technicians at 05 86 24 00 26 with the machine model and leak location

Suspended front axle Case IH Puma and CVX: technical features

Case IH Puma CVX and CVX 130 tractors feature a hydraulically suspended front axle controlled by an electronic traction management unit. This system absorbs ground irregularities at transport speeds (up to 50 km/h), reduces operator fatigue, and limits road bounce. The suspended axle includes hydraulic suspension cylinders, a position sensor, and an integrated valve block. Common failures include wear of cylinder seals, leaks in the hydraulic block, and positioning faults. In case of failure, replacing with a used complete front axle inspected in our workshop remains the fastest and most cost-effective solution on machines no longer under manufacturer warranty.

Case IH Puma and CVX tractors mainly receive ZF MT series axles (for suspended models) or TS series (rigid axles). The exact reference depends on power, year of manufacture, and presence or absence of integrated suspension. To identify the axle on your machine, provide the serial number of your tractor and the axle number (stamped on the housing) to our technical team at 05 86 24 00 26.

Compatibility of a front axle is verified on three criteria: axle family (ZF, Dana, or other), gear ratio (ratio of bevel gear and wheel reducer), and the mounting dimensions on the cradle. Simple model matching is not always sufficient, as Case IH has updated axles during production runs on long series (Maxxum, Puma). Our technicians can assist you in finding the exact reference from our available stock, using your machine identification details.

Yes. After installing a used complete front axle, adjusting the backlash of the bevel gear (bearing preload) is essential, along with checking the alignment and camber of the steering wheels. Incorrect bevel gear adjustment leads to rapid gear wear and abnormal housing temperature rise. TMC Bejenne delivers axles inspected in the workshop, but final installation adjustment must be performed by a qualified technician during tractor assembly.