Show the number+335 86 24 00 26

Used Tractor Hitch

136 available products

A cracked drawbar eye or a seized pick-up hook can halt the entire transport chain. TMC Bejenne offers a wide selection of used hitch parts: drawbar eyes, hooks, oscillating bars, hole bars, and pins. For 3-point hitches, the lifting range complements our offer with lower arms, upper arms, and stabilizers. Each part is inspected in our workshop before shipment, available immediately, and offered at prices lower than new parts.

 CASE IH(21)
 CLAAS(13)
 DEUTZ FAHR(11)
 FENDT(3)
 FIAT(2)
 FORD(4)
 JOHN-DEERE(17)
 Kubota(1)
 MASSEY FERGUSON(10)
 MERLO(3)
 NEW-HOLLAND(37)
 RENAULT(4)
 SAME(3)
 STEYR(1)
 VALMET(1)
 VALTRA(3)

Tractor drawbar eye: the most stressed part

The drawbar eye absorbs every pull and brake force from the trailer. Over time, the pin ovalizes, adjustment holes wear out, and the play becomes dangerous on the road. Our used drawbar eyes come from tractors dismantled in Naintré, across a 11-hectare facility. Our specialized technicians check for cracks, bore condition, and straightness before putting them up for sale.

Tractor hitch parts and bars at TMC Bejenne

  • Agricultural tractor drawbar eye, with pin or height adjustment
  • Hitch hook and hydraulic pick-up hook for trailers
  • Oscillating bar and hole bar for towed implements
  • Fixed pin for heavy trailers and slurry tanks
  • Agricultural tractor hitch ball for rapid transport
  • Axles, pins, and shims for drawbar eyes

Tractor trailer hitch: drawbar eye, hook, or ball

The choice depends on the load, speed, and type of trailer. The drawbar eye remains the most common solution for tipper and flatbed trailers. The pick-up hook allows hooking up from the cabin, a real time saver during ensiling or harvesting periods. The pin supports the high vertical loads of slurry tanks. The agricultural tractor hitch ball is found on modern transport hitches. Provide your configuration, and we will guide you to the suitable part.

3-point tractor hitch: types and dimensions

  • Hitch category: 1 for small tractors, 2 for medium power, 3 and 4 for high horsepower
  • Diameter of ball joints and pins, to be checked on both the implement and the tractor
  • Center distance between lower arms and height of the upper hitch point
  • Manufacturer reference engraved or noted on the removed part
  • Exact model, year, and tractor serial number
  • Photos of the worn part for quick identification

Tractor hitch for Massey Ferguson, IH, Renault, John Deere

Our stock covers major agricultural brands. You'll find hitches for Massey Ferguson , highly sought after from the 6000 and 7000 series, as well as for John Deere and Case IH , including older IH models. Models from Renault , New Holland , Fendt , and Deutz-Fahr are also represented. For an IH tractor drawbar eye or a Renault hook, provide us with the model: we verify compatibility with the part in stock.

Agricultural tractor dismantling: the advantage of deconstruction

  • Parts removed from dismantled tractors, never from unknown batches
  • Quality control in our workshop by specialized technicians
  • 25,000 references permanently in stock across all categories
  • 90% of requests fulfilled
  • Savings of 30 to 70% compared to new parts
  • Second life of components following a circular economy approach

Hitch parts: inspections and regular maintenance

A well-maintained hitch lasts as long as the tractor. Regularly grease the pins and the mechanism of the pick-up hook. Check the play between the pin and the drawbar eye: a knocking noise at startup indicates advanced wear. Replace deformed pins without delay. For 3-point hitches, also check lower arms and stabilizers, which often wear out at the same time. Models equipped with front lift deserve the same attention.

At TMC Bejenne, specialists in used agricultural parts since 1945. Drawbar eyes, hooks, and bars come from tractors dismantled in Naintré and are inspected in our workshop. The lifting range completes our hitch offer. Call +33 5 35 54 42 10 for a quote. We ship throughout France.

The drawbar eye requires leaving the tractor to engage the pin. The hydraulically controlled pick-up hook lifts to hook the trailer ring from the cabin. It's suited for frequent hitching, such as ensiling sites. The drawbar eye remains simpler and less costly to replace. Our technicians help you choose based on your usage and Massey Ferguson , John Deere , or other model.

The category is noted in the tractor's manual and can be verified by the diameter of the lower arm ball joints. Small tractors use category 1, medium powers use category 2, and high-horsepower tractors use categories 3 and 4. If in doubt, measure the pin diameter and arm center distance, then contact us. The lifting range covers related parts.

Price depends on the type of hitch – drawbar eye, pick-up hook, pin, or oscillating bar – and tractor model. A checked used part costs 30 to 70% less than a new one. Installation costs vary by workshop and time required. Request a quote for the part at +33 5 35 54 42 10 and consult the lifting range for associated parts.

Provide the tractor's brand, model, and year, along with the reference noted on the part if legible. A photo and some measurements (pin diameter, center distance) speed up identification. For an older Case IH or Renault , the original reference is the most reliable way. Our technicians then compare it with the available part.

You can request a quote directly from the part's page or by phone at +33 5 35 54 42 10. Our team confirms compatibility, availability, and shipping times. With 25,000 references in stock and a 11-hectare facility, TMC Bejenne fulfills the vast majority of requests, including for older models.

Can't find the part you're looking for?

Fill out this form or contact us at 05 86 24 00 26

* Required fields