Used Case IH Cylinders: Hydraulic and Pneumatic Components

Our expertise in the agricultural sector allows us to offer hydraulic and pneumatic cylinders suited to the most common Case IH tractors. These essential components withstand high pressures during intensive agricultural work.

Steering cylinders feature proven technology with corrosion-resistant chrome-plated rods. Their diameter typically ranges between 45 and 70 mm depending on the Case IH tractor model. Gas cylinders for cabin doors provide working forces between 200 and 450 Newtons.

Each reference meets original specifications to ensure reliable operation. Sealing rings and repair kits often accompany our refurbished cylinders, enabling optimal restoration of your agricultural equipment.

Case IH Steering and Steering Column Cylinders

• Case IH steering cylinders ensure precise maneuverability of the 3000, 4000, and CX series tractors.
• Powered by an orbitrol, these hydrostatic cylinders act directly on the steering ball joints.
• Compatible with original references 188842A1, 549667R91, and 84336125 for models 385 to 995 XL.
• The steering column sometimes includes one or two cylinders depending on the tractor configuration.
• Seal kits 83957762 allow complete renovation of cylinders with 45 mm diameter rods.
• Installation is eased by standardized hydraulic fittings and preserved original mounts.
• Optimal performance on tough terrain with heavy loads thanks to enhanced hydraulic assistance.

Power Steering Cylinders

These hydraulic components provide exceptional maneuverability even under the most demanding conditions. Their robust design resists significant mechanical stresses during repeated maneuvers on rough terrain.

Operating pressure generally ranges between 150 and 200 bars depending on the Case IH models involved. This hydraulic power drastically reduces steering effort, decreasing operator fatigue during long working days.

Preventive maintenance of these cylinders significantly extends their service life. Regular checks of hydraulic oil levels and periodic seal replacements maintain original performance. The quality of hydraulic fluid directly impacts the responsiveness of the power steering system.

Steering Seals and Repair Kits

• Steering repair kits include O-rings, oil seals, and sealing rings specific to Case IH tractors.
• Kit reference 83957762 is compatible with steering cylinders for the 3000, 4000, CX, and MX Case IH series.
• Materials withstand high hydraulic pressures up to 200 bars and extreme agricultural temperatures.
• Input shaft oil seals are available in size 70 x 90 x 13 mm for Case IH models.
• Installation is recommended during complete cylinder disassembly to avoid recurring hydraulic leaks.
• Compatibility extends to original references 061235R1, 21000012AA, and 752865 depending on tractor models.
• Preventive replacement of seals every 2000 operating hours ensures perfect sealing.

Cabin Door and Windshield Gas Cylinders

Case IH cabin pneumatic cylinders use compressed gas technology to facilitate door opening and closing. Their working force ranges from 200 to 450 Newtons depending on the tractor models concerned. Reference 3232937R1 notably fits XL series such as 745XL, 845XL, 956XL, and 1255XL.

These components typically measure 275 to 280 mm in closed length with a stroke of 85 mm. Their outer diameter of 18 mm and 8 mm rod ensure low intrusion inside the cabin. Standardized mounting ends simplify onsite replacement without special tools.

Checking dimensions is essential before any replacement. Inadequate force can damage cabin windows or compromise safety. Refurbished cylinders maintain original performance while offering an economical alternative to new parts.

Tractor Door Pneumatic Cylinders

• Simplified installation thanks to pre-installed M8 ball joints on Case IH models 3220, 3230, 4210 to 4240.
• Pressure control is necessary before installation since 10 Newton approximately equals 1 kilogram of thrust.
• Replacement is recommended in pairs to maintain perfect balance during opening and closing movements.
• Extended compatibility with XL cabins from series 485XL to 995XL, with possible adaptation to Ford series 10.
• Average lifespan of 3000 opening cycles under intensive agricultural use depending on operating conditions.
• Vertical storage advised to preserve gas sealing and prevent premature pressure loss.

Rear Window and Windshield Cylinders

Case IH rear window and windshield cylinders have technical features distinct from door models. Their reduced pushing force of 150 to 250 Newtons effectively protects glass surfaces from excessive stress. These pneumatic components primarily equip Maxxum, Puma CVT, and T series with lengths ranging from 300 to 490 mm depending on applications.

Reference 82022486 fits perfectly on Maxxum 100 to 140 and Puma CVX tractors with a length of 490 mm. Direct installation replaces faulty cylinders without modifying original mounts. Checking stroke and force is essential since incorrect sizing can cause glass cracks or block opening mechanisms.

Replacement is recommended in pairs to maintain movement balance. Standard ends facilitate adaptation across different Case IH series while preserving perfect pneumatic system sealing.

Puma and Other Series Hydraulic Lift Cylinders

• Higher lifting power than original cylinders thanks to chrome-plated rods with 70 mm diameter instead of the standard 65 mm.
• Closed length of 400 mm and extended stroke up to 643 mm for Puma CVT, CVX, and Maxxum tractors.
• Performance gains of 10 to 25% depending on chosen rod diameter to optimize rear lifting capacity.
• Direct mounting with 9;22 mm ball joints and hydraulic fittings identical to original Case IH specifications.
• Delivered with black protective coating and reuse of existing fittings to simplify installation.
• Wide compatibility with MX, Magnum, and Steiger series with operating pressures up to 250 bars maximum.
• Replacement recommended in pairs to maintain lifting stability and avoid agricultural implement imbalances.